What are the Maintenance Precautions for Automatic Capsule Filling Machine?

 As a China Pharmaceutical Equipment Manufacturer, share with you. The capsule filling machine is an intermittently operating, fully automatic hard capsule filling equipment with orifice disk metering. It has a precise design and stable operation. It can automatically complete sac inflating, sub-capsulation, filling, waste sac removal, lock sacs, export of finished products, etc. Kind of process. Fully enclosed ten-station turntable, module single-row die hole 9-hole design.

Automatic Capsule Filling Machine

The following editor briefly introduces the maintenance precautions of the capsule filling machine, as follows:

1. The oil quantity of the main drive reducer should be checked once a month. If it is insufficient, the oil should be refueled in time, and the lubricant should be replaced every six months. The lubricant should be replaced once every 3000h of the indexing box of the turntable. According to experience, 90 #机油.

2. The vacuum separator of the vacuum system mainly plays the role of sucking the capsule into the upper and lower modules and separating the cap and the body during the filling of the hard capsule. If the capsule cannot separate the cap and the body, the subsequent filling will not be possible. Every time the turntable of the machine rotates one station, the main shaft of the machine rotates one round, and the vacuum separator moves up and down once under the action of the cam. If the cap and body of the capsule are not separated smoothly, check the gap between the upper plane of the vacuum separator and the lower plane of the lower module. If the gap is too large, the vacuum degree of the vacuum system will not reach the vacuum degree required by the cap and body separation ( About 0.05MPa), the gap is too small and it is easy to cause head collision to deform the lower module. When the position of the vacuum separator needs to be adjusted, use the handle to turn the main motor shaft to raise the vacuum separator to a high position, and loosen the lock nuts at both ends of the adjusting rod under the machine table (one is left-handed nut, one is right-handed nut ), then turn the adjusting rod to adjust the height of the vacuum separator, then tighten the nut, and use the handle to rotate the main motor shaft to test until it is suitable. The vacuum degree is read on the vacuum gauge on the operation panel of the machine. When the vacuum is too high, the vacuum degree regulating valve can be opened appropriately, and when the vacuum is too low, the vacuum degree regulating valve can be closed or closed. The filter of the vacuum system should be opened regularly to remove the clogged dirt to ensure that the vacuum system has sufficient vacuum.

3. The transmission mechanism under the working table of the machine should always add lubricating oil (grease) in an appropriate amount to reduce the wear of moving parts.

4. The safety clutch plays a protective role when the machine is overloaded. The clutch should not slip when the load is normal, but it may also slip due to long-term use. When slipping occurs in normal use, the round nut of the clutch can be tightened. Some, in order to achieve the purpose of ensuring the normal operation of the machine and protecting it.

Our company also has Automatic Capsule Filling Machine on sale, welcome to contact us.

评论

发表评论

此博客中的热门博文

Parameters To Be Controlled In Fluid Bed Dryer

图片
Fluidized bed dryer (also referred to as  Fluid Bed Dryer ) is a sort of equipment utilized widely in the pharmaceutical businesses to decrease the moisture content of pharmaceutical powder and granules. In fluidization procedure, warm air is released in high pressure through a perforated bed of moist sound particulate. The moist solids have been raised from the ground and suspended in a flow of air (fluidized condition ). Heat transfer is achieved with direct contact between the moist strong and warm gases. The vaporised liquid is taken off from the drying gasses. Sometimes to conserve energy, the flow gas is partly recycled. To be able to boost performance, efficacy, and reproducibility of a fluidized bed drier, a few parameters will need to be controlled.  Fluid Bed Dryer Manufacturer  will tell you its parameters. Device parameters: People controlled by the equipment. Procedure parameters: People controlled by the Process. Merchandise parameters: People contr...
阅读全文

Types Of Pharmaceutical Equipment

图片
The pharmaceutical industry has the most exact requirements and production guidelines concerning quality. Because of this, it's essential that pharmaceutical production supplies comply with good manufacturing practice (GMP).  Pharmaceutical Equipment  contains a vast array of gear, including  Automatic Capsule Filling Machine , x-ray review methods , and spray drying fittings . To be able to guarantee precise formulation and manufacturing development, virtually every procedure can be automatic. Consequently, there's a slice of pharmaceutical manufacturing equipment required with each step. Generally, it is divided into two parts. Processing equipment and Packaging equipment. As one of the Best  Pharmaceutical Equipment Exporter , Canaan Technology Understands the intricate nature of pharmaceutical production. Contact us now To observe how our equipment can help you.
阅读全文

High Speed Development Trend of Roller Compactor

图片
Pharmaceutical is a complex process, which requires many processes, and  High Quality Roller Compactor  is an important part of it. Therefore, the role of  Roller Compactor  in the pharmaceutical industry is very obvious. With the development of the pharmaceutical market, the requirement for pelletizer is increasing day by day. Roller Compactor is a kind of swinging action of rotary drum. It can grind wet powder raw materials into granules by wire sieve. It can also be widely used for grinding granules which have become lumps and ready-made granules. A lump formed during lump forming or during chemical processing. With the continuous development of the industry, roller compactor machine began to emerge. It is a new roller compactor method developed after the second generation granulation method. it is an environmental friendly granulation process. it is a new equipment for directly pressing powder into granules. We are  Roller Compactor Manufacturer ...
阅读全文